Tools/Maintenance

• Service kits include air can seals and wiper • Available for RockShox air rear shocks--Ario, Monarch, Monarch RT3, DebonAir and Monarch Plus

• Essential mechanic tool to properly service and maintain all RockShox products • For RockShox Monarch

RockShox, 00.6815.066.020, Reverb post bleed tool

Tools for repair and maintenance of RockShox Reverb suspension seatposts. - Specific to RockShox Reverb post

Rear Shock Air Valve Adapter (for charging IFP) - SIDLuxe A1+ (2020+)

This is RockShox's recommended cleaner for suspension internals. Handy aerosol spray degreases and conditions small parts like O-rings and seals. - Formulated with special conditioners that will not cause O-rings and seals to dry, crack, or degrade - For use on all suspension products

SRAM's Butter Grease is a Slickoleum lube recommended for fork bushings, Roam and Rise wheel rear hub pawls and Reverb seat post service. Keep your parts working smoothly!

- Single 29mm open bore drift for use with 1/2" rods

This 29mm open bore adapter is used to press 29mm x 42mm (DUB) sealed bearings. The adapter is machined with one step at 29mm OD, which fits into the center of the sealed bearing. For use with Wheels Mfg. bottom bracket press (PRESS-7 , PRESS-7-PRO or PRESS-9-PRO). - Inner step outer diameter: 28.9mm - Outer diameter: 41.8mm - Thru hole diameter: 12.8mm (1/2-inch) - Thickness: 7mm - Machined, red anodized aluminum - Sold individually

Wheels Manufacturing open bore adapters are used to press sealed cartridge bearings into place. The adapters are machined with one step to correspond to the bearing OD, which fits in to the center of the sealed bearing and an outside diameter to accommodate the bearing's outer diameter. Size: [Bearing inner diameter] x [Bearing outer diameter] Note: If only one dimension is given, that is the outer diameter of the adapter, with no inner diameter step

Wheels Manufacturing Over Axle Adapters are used for pressing your most commonly used bearing sizes into place. Each represents an excellent addition to the Press-4 Bearing Press. - Adapters sold individually

Our 2437 open bore adapter is used to press 24x37 sealed bearings into bottom bracket cups, and direct fit frames like trek BB90. The adapter is machined with one step at 24mm ID, which fits into the center of the sealed bearing. - Installs: 24x37 bearing - Inner step outer diameter: 23. 8mm - Outer diameter: 36. 8mm - Thru hole diameter: 0. 387" (9. 8mm) - Inner hole sized to fit 1/2" threaded rod - Compatible with BP0006, BP0007 - Machined, red anodized aluminum - Sold individually (2 drifts required for some installations)

Our 6806 open bore adapter is used to press 42x30 sealed bearings. The adapter is machined with one step at 30mm ID, which fits into the center of the sealed bearing. Common bearing size for BB30 frames and bottom brackets. - Installs: 6806 bearing - Inner step outer diameter: 29. 9mm - Outer diameter: 41. 8mm - Thickness: 7mm - Thru hole diameter: 0. 387" (9. 8mm) - Inner hole sized to fit 1/2" threaded rod - Compatible BP0006, BP0007 - Machined, red anodized aluminum - Sold individually (2 drifts required for some installations)

Our GXP-LEFT open bore adapter is used to press 22x37 sealed bearings into SRAM GXP bottom bracket cups and direct fit frames like trek BB90. The adapter is machined with one step at 22mm OD, which fits into the center of the sealed bearing. - Installs: 22x37 (GXP) bearing - Inner step outer diameter: 21. 9mm - Outer diameter: 36. 8mm - Thickness: 7mm - Thru hole diameter: 0. 387" (9. 8mm) - Inner hole sized to fit 1/2" ACME threaded rod - Compatible with BP0006, BP0007 - Machined, red anodized aluminum - Sold individually

- Telescoping magnetic (pen) tool with pocket clip - Ideal for retrieving hard-to-reach, ferrous-metal objects - Powerful magnetic tip will hold up to a 2lb object - 5-1/2" long tool with up to 23-1/2" full extension

Park Tool's Replacement Chain Tool Pin fits Park Tool's CT-6, CT-6.2, and CT-6.3 Chain Tools (each sold separately). • Made from hardened alloy tool steel • NOTE: The 985-1 will also push out the chain rivet completely from the chain side plate.

- Replaces original Shimano bleed fitting with easy to use lever reservoir bleed fitting

- Grease for periodic maintenance of suspension/dropper seatposts - Works well on most shocks and forks

Everyone wears out their Park Tool work stand clamp covers at some point. Find replacement covers for yours here. Each cover is constructed of soft, durable composite rubber. See below to determine which covers fit your Park Tool stand clamp: - 1002: fits 100-3X and 100-5X extreme range clamps - 1185: fits clamps on the repair stands PCS-9, PCS-10, PCS-11, and PCS-12 - 1259: fits 100-4X, 100-6X, 100-7X, and 100-15X clamps - 1960: fits 100-3D, 100-5D, and 100-25D Professional Micro Adjust Repair Stand Clamps - 468B: fits clamps with double cable reliefs, including 100-3C, 100-5C, 100-8C, 100-8Y, and 100-9C clamps - 467B: fits clamps with single cable relief, including PRS-2 through PRS-8 (for older-style clamps, non-current) - 468G: fits PCS-1 and PCS-2 clamps with double cable reliefs (clamp models: 100-1C, 100-1CA, and 100-2C) - 467G: fits PCS-1 and PCS-2 clamps with single cable relief (for older PCS-series stands only; not for current model stands) - 466: Rubber Replacement Clamp Cover Set (fits older clamps with plastic-dipped jaws)

- Film forming lubricant designed to protect moving components and wear surfaces during assembly and initial break-in - Shields metal-To-metal contact and offers excellent rust and corrosion protection during long service periods and storage - Formulated with high levels of anti-Wear and extreme pressure additives and surface active chemistry to reduce friction. Two times zinc activates at both high and low operating temps providing unsurpassed protection. Non-Foaming

- Ultra-Clean, waterproof formula chain lube designed for use in dry conditions - Surface active chemistry promotes smooth shifting under load, quiets chain noise and significantly improves life of drivetrain - Fast penetration and setup promotes a clean, trouble-free operating environment in dry, dusty conditions

- Goes on wet to penetrate rollers and side plates, then sets up to a soft, pliable wax - Chain is encased in a waterproof layer, shielded from dirt and grime - Special low melt point wax replenishes drivetrain by slow-Feeding clean lube from the inside layers outward, significantly reducing abrasive wear and eliminating corrosion - Smooth, quiet, trouble-free operation in all conditions for long lasting protection

- Exclusive 100% synthetic bike chain lube - Special surface active formula reduces rolling resistance of drivetrain and improves shifting performance - Deep chain penetration ensures quiet operation - Waterproof formula protects drivetrain under load and extends chain life

Park's Anti-Seize Compound reduces friction in threaded and press fit connections for easy assembly and disassembly. It's ideal for bottom brackets, pedal threads, headset cups, seatposts, quill stems and much more. This compound also seals and protects parts from corrosion and rust under the most extreme conditions.

Park's Bladed Spoke Holder is a must for building and truing wheels that feature bladed spokes. It has 4 different size slots to fit a wide variety of bladed (aero) spokes from .08 to 2mm wide. It holds them safely in place to prevent twisting as you turn the nipple to true and tension the wheel.

Heat-treated alloy tool steel, one inch base fits wrench or bench vise. Thin-wall construction allows use without removal of cones and locknuts. The FR-5 has 12 splines that are approximately 23.4mm across. - Fits Shimano, SRAM, Sunrace, Suntour, Chris King and other cassette lockrings - Fits the SRAM XX1 11-speed cassettes - Also fits Shimano disc brake lockrings - Always use a quick-release skewer to hold the tool in place and snug to cogs when loosening; for solid axles, use the axle nut

Regular lubrication of bicycle chains addresses annoying squeaks and noises, and extends the life of the chain and drivetrain components. Formulated using a proprietary blend of oils, Park Tool CL-1.2 Chain Lube works great in wet or dry conditions. It penetrates, reduces friction, prolongs component life, displaces moisture, and protects parts from rust and corrosion. Compatible with all bicycle chains. Also works great as general-purpose light lubricant for use on bicycle brake and derailleur cables and housing, spoke nipples, and derailleur and brake pivots. - 4 fl. oz. (118 mL) bottle NOTE: Some painted surfaces can be sensitive to oil and grease. Clean off any excess oil or grease immediately. Test first on an inconspicuous area to see if it causes a stain or discoloration.

A handy tool designed to make installation and removal of bicycle electronic shifting wires and batteries quick and easy. - Durable composite body is durable and prevents scratching of expensive components - Angled Shimano Di2 E-TUBE ends allow for both installation and removal in tight spaces - Universal coin cell tool helps remove and install battery covers on SRAM eTap

Park's Offset Brake Wrench utilizes a unique design that allows it to reach into tight areas that other wrenches cannot. The OBW-3 features a 14mm wrench on one end and the other end fits into a brake's tension springs to rotate the brake around its bolt for proper alignment. The OBW-4 features 10-, 11-, 12-, and 13-mm opening to fit most models of sidepull brakes.

Park Tool is world-renowned for their bicycle industry tools, and their pumps are no exception. Keep yours up to speed and working smoothly with these rebuild kits. - 1096K: Contains one #1081 head as well as one #1075 plunger gasket for older PFP-2 and first generation PFP-4 floor pumps. Also compatible with second-generation PFP-4 floor pumps. - 1096X: Contains one #1096R head, one #1472 fitting, and one #1075 plunger gasket for second generation PFP-4 floor pumps. Also compatible with PFP-2 and first-generation PFP-4 floor pumps. - 1096Z: Contains one #1096R head, one #1472 fitting, and one #1087 plunger gasket for PFP-5 and PFP-7 floor pumps. Also compatible with PFP-3, PFP-6, and PFP-8 floor pumps.