Parts & Accessories

Looking for a super lightweight but badass tubeless sealant? Boom, you've just found it my friend! No Puncture Hassle performs under the most brutal race conditions. The cutting-edge microfiber molecules fill the bigger holes and tears, whilst the advanced latex forms a strong seal instantly. The formula also contains a unique UV detection system that highlights any punctures you haven’t seen during your ride. Developed with the world's top downhillers and pro peloton teams, to give you the finest tire sealant available. It's non-corrosive and easily washes off with water. Compatible with tubeless ready and full UST wheels/tires, No Puncture Hassle works from 15psi-120psi and temperatures from -20°C to +50°C. Our pouch is designed to fit your Presta valve perfectly and is ideal to add to your toolkit or ride pack for emergency top ups on the go! - For Downhill, Enduro and Road tires - Seals tears and holes up to 6mm - Contains UV puncture detection - Won't dry out or ball - Works from 15psi-120psi and temperatures from -20°C to +50°C - Biodegradable

Make your WTB rims air tight and ready for tubeless use with WTB's TCS Rim Tape. This tape covers the spoke holes and can be used as a lightweight rim tape in any rim. Available in 11-meter (covers 5 rims) and 55-meter rolls (covers 27 rims).

We designed Teravail tubeless tape for no-hassle installation. Its slight stretch allows the tape to easily conform to your rims. The translucent material shows you exactly where the tape makes contact. It's tacky enough to prevent shifting but easy to pull up if needed, and it won't leave residue on your rims. - Teravail Tubeless Tape comes in a variety of widths to fit almost any rim. - Teravail Tubeless Tape is available in a variety of widths and roll lengths. - Ten-meter length is enough for a single layer on approximately four wheels

The buyer's choice for wheel builders looking to save weight. The nipples are available with or without DT Pro Lock, a patented liquid inside the nipple thread that makes the connection between the nipple and spoke extremely durable. It pairs perfectly with any wheel, though all-brass nipples are recommended for e-bike use. - Weight: starting at 20g for 64 nipples

Wheel Conversion Caps for Zipp 77/177 Disc hubs. Converts your Zipp 77 or 177 hubs to nearly any frame standard.

SRAM's X0 conversion caps are the ticket for converting your X0 hubs to a different axle type.

Can be used with Stan's ZTR rims to make them airtight or used as a lightweight rim tape in any rim. A single 10-yard roll will tape five 26-inch rims or four 29-inch rims or two wide road clincher rims. 21mm width fits: - ZTR Olympic - ZTR Iron Cross - ZTR 355 - ZTR Alpine - ZTR Crest - ZTR Alpha 340 (2 layers) - ZTR Alpha 400 (2 layers) - Most road clincher rims 25mm width fits: - ZTR 355 (26", 650b, 29") - ZTR Crest - Crest MK3 - ZTR Arch EX - ZTR Flow EX - Crest S1 27mm width fits: - ZTR Flow EX - ZTR Bravo - ZTR Hugo 52mm - Arch S1 - ZTR Rapid 28 - ZTR Rapid 30 - Arch MK3 30mm width fits: - ZTR Flow MK3

Booster thru-axle hub spacer kits are designed to give your non-Boost front and rear thru-axle hubs the boost they need to fit any Boost-compatible frame or fork.

The Muc-Off Tubeless Rim tape is made from their proprietary performance material with a pressure-sensitive adhesive to provide just the right amount stretch whilst maintaining durability and strength needed to create a lasting airtight seal. Semi-transparent material makes locating the valve hole easy.

Developed for short spokes with a large deflection angle. DT Pro Head nipples are designed for short spokes with a large angle of deflection, such as for e-bike use. Through the spherical contact surface, the nipple aligns automatically with the angle of the spoke, which leads to consistent power transmission. Note: brass nipples are not approved for children's products in the USA. See attached warning! All-brass nipples are recommended for e-bike use. - Weight: starting at 59g for 64 nipples.

- 3-piece kit to secure wheels and seatpost - Lighter and safer than regular QR skewers - MTB 100mm/135mm - Seatpost: M6 x 45mm

Thru-Axle hub adapters allow the use of 100 mm front thru-axle hubs in 100 mm QR forks. -Allows the use of modern thru-axle wheels in forks designed for quick-release compatible hubs -100 mm front hub spacing only -CNC-machined AL-6061

- Front axle conversion, 15mm thru-axle, Wide Boy - Conversions for fitting a Wide Boy hub onto either a 15mm or 20mm thru-axle fork

- Rear axle conversions for Spin Doctor Pro rear hub - Various replacement axles and conversion kits for Spin Doctor and Spin Doctor Pro hubs - Some conversions utilize pre-existing axle components for retrofit - Conversion kits for original Spin Doctor and Spin Doctor Pro hubs are not compatible with Spin Doctor 6-Drive hubs

- Rear axle replacement kit, 10mm nutted, DJD-SupaD - Spin Doctor, Spin Doctor Pro and Spin Doctor 6-Drive parts are generally not cross compatible - DJD and DJD-BD parts are generally not cross compatible

- Tubeless Compatible System rim tape provides an airtight seal between rim and tire - WTB recommends using tape that is 5mm wider than the inner rim width - An 11 meter roll will covers five wheels and a 55 meter roll covers 27 wheels

Trainer Caps allow thru-axle bikes to be used with most wind, magnetic or fluid cycling trainers. Cold weather and short days are never far from a Minnesotan's mind so Wolf Tooth engineers created Trainer Caps to reduce barriers to winter workouts. Non-drive side axle caps are joined by drive-side plugs that can be installed or removed without tools to make the prospect of hopping on the trainer a little more bearable. - Compatibility: Wolf Tooth Rear Axles (not compatible with rear axles from other manufacturers) - Plug has O-ring retention – no tool required

Elite Series skewers for fat bike applications AL6061 alloy lever with CrMo axle Available for 135mm, 150mm, 170mm, and 190mm OLD spacing

SRAM's Rise 60 conversion caps are the ticket for converting your Rise 60 wheels to a different axle type.

WeThePeople's Supreme Hub Guards are made of low-friction nylon fiberglass. Simply replace the cones on your Supreme Front and Cassette Hubs for a perfect fit without having to spread your dropouts. Available for both front and rear. These guards now feature a heat-treated chromoly insert for longer life.

- Non-quick release design for added security - Alloy anchor nut includes Anti-Spin tab which prevents unwanted turning of nut when tightening or loosening the hex through-bolt - XL version compatible with thicker dropouts (up to 10mm thick) - Torque to 7 N - Wheel: front/rear - Spacing (front/rear): 100/135mm - Shaft: Chromoly

Authentic service bearing kit for Ritchey mountain bike wheels. - Replacement bearings for Vantage V1 non-2pc hubs

These bobbins are made by the Robert Axle Project and are identical to the bobbins that came with your original BOB skewer. Slide them on your axle ends to complete your Robert Axle thru axle for BOB Trailer. - Sold in pairs - Manufactured from 303 Stainless Steel - Includes stainless steel hardware for attaching to axle

Replacement rear axle for Neo and Neo Ultimate hubs. High-precision center-less ground treatment ensures perfect bearing fit.

- Extra security against theft - 5mm hex CrMo axle

Pro Head Reinforcement System (PHR) has a larger and more spherical contact area and is designed to balance loads transferred to the rim. The PHR system acts as a ball and socket interface, allowing the spoke to pivot into alignment while maintaining even, consistent contact during installation in order to follow the perfect trajectory from the hub to the rim.

Parts for RaceFace hubs.

Shimano Nexus and Alfine Internally Geared Hub Cassette Joints - Shimano model # CJ-S7000 - Does not include cable fixing bolt unit - OEM cassette joint unit for Alfine SG-S7000-8

Use Stan's Tubeless Valve Stems when you're converting standard rims to tubeless via the taping method. These also have a removable core for easier application of tire sealant. Note: Schrader valve is for non-stepped Hugo rims. If your Hugo rim decal reads: - MAX RIM PRESSURE: 2.8 tires: 26psi, 3.0 tires: 24psi - ERD 615, 622x49.9, 29 in x 52.3mm Your rim has a stepped valve and is not compatible with this Schrader valve.

WTB's TCS Brass Valves are your key to the excellence that is tubeless wheels and tires. A stepped lock nut adds compatibility among various rim drillings, a smooth pump interface makes adding air easy, and a removable core makes setting beads and injecting sealant a cinch.